View ZL40162DCB_1339147.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ZL40162 High Output Current High Speed Dual Operational Amplifier
Data Sheet Features
* High Output Drive * 18.8 Vpp differential output voltage, RL = 50 * 9.4 Vpp single-ended output voltage, RL = 25 High Output Current * 200mA @ Vo = 9.4 Vpp, Vs = 12V Low Distortion * 83dB SFDR (Spurious Free Dynamic Range) @ 100KHz, Vo = 2Vpp, RL = 25 High Speed * 158MHz 3dB bandwidth (G=2) * 195V / s slew rate Low Noise * 3.8nV / Hz: input noise voltage * 2.7pA / Hz: input noise current Low supply current: 7mA/amp * Single-supply operation: 5V to 12V High ESD (Electro-Static Discharge) immunity * 4kV for Supply and Output pins Low differential gain and phase * 0.01% and -0.1deg Ordering Information ZL40162/DCA ZL40162/DCB (tubes) 8 lead SOIC (tape and reel) 8 lead SOIC
April 2003
* *
-40C to +85C
Description
The ZL40162 is a low cost voltage feedback opamp capable of driving signals to within 1V of the power supply rails. It features low noise and low distortion accompanied by a high output current which makes it ideally suited for the application as an xDSL line driver. The dual opamp can be connected as a differential line driver delivering signals up to 18.8Vpp swing into a 25 load, fully supporting the peak upstream power levels for upstream full-rate ADSL (Asymmetrical Digital Subscriber Line).
*
*
* * *
Applications
* * * ADSL PCI modem cards xDSL external modem Line Driver
Out_1
1
8 V+ 7 Out_2
In_n_1 2
1
In_p_1 3 6 In_n_2
2
V- 4
ZL40162
5 In_p_2
Figure 1 - Functional Block Diagram and Pin Connection
1
ZL40162
Application Notes
Data Sheet
The ZL40162 is a high speed, high output current, dual operational amplifier with a high slew rate and low distortion. The device uses conventional voltage feedback for ease of use and more flexibility. These characteristics make the ZL40162 ideal for applications where driving low impedances of 25 to 100 such as xDSL and active filters. The figure below shows a typical ADSL application utilising a 1:2 transformer, the feedback path provides a Gain = +2.
12R5 Rf1 Rg Rf2 12R5 100R
Figure 2 - A Typical ADSL Application A class AB output stage allows the ZL40162 to deliver high currents to low impedance loads with low distortion while consuming low quiescent current. Note: the high ESD immunity figure of 4kV may mean that in some designs fewer additional EMC protection components are needed thus reducing total system costs. The ZL40162 is not limited to ADSL applications and can be used as a general purpose opamp configured with either inverting or non-inverting feedback. The figure below shows non-inverting feedback arrangement that has typically been used to obtain the data sheet specifications.
Rf Rg
Figure 3 - A Non-Inverting Feedback Amplifier Example
2
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Absolute Maximum Ratings - (See Note 1)
Parameter Vin Differential Output Short Circuit Protection Symbol VIN VOS/C Min Max 1.2 See Apps Note in this data sheet 13.2 (V-) -0.8 (V+) +0.8 5.5 4 -55 +/-100mA for 100ms 20% pulse for 100ms (Note 3) +150 (Note 4) (Note 5) V V V kV C Units V
Supply Voltage Voltage at Input Pins Voltage at Output Pins ESD Protection (HBM Human Body Model) (See Note 2) Storage Temperature Latch-up test Supply transient test
Note 1: Note 2: Note 3: Note 4: Note 5:
V+, VV(+IN), V(-IN) VO
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Human body model, 1.5k in series with 100pF. Machine model, 200 in series with 100pF. 1.25kV between the pairs of +INA, -INA and +INB, -INB pins only. 4kV between supply pins, OUTA or OUTB pins and any input pin. +/-100mA applied to input and output pins to force the device to go into "latch-up". The device passes this test to JEDEC spec 17. Positive and Negative supply transient testing increases the supplies by 20% for 100ms.
Operating Ratings - (See Note 1)
Parameter Supply Voltage Junction Temperature Range Junction to Ambient Resistance Rth(j-a) Symbol V+, VMin 2.5 -40 150 Max 6.5 150 Units V C C 4 layer FR5 board C 4 layer FR5 board
Junction to Case Resistance
Rth(j-c)
60
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Zarlink Semiconductor Inc.
3
ZL40162
otherwise specified Symbol
Data Sheet
Electrical Characteristics - TA = 25C, G = +2, Vs = 6V, Rf = Rg = 510, RL = 100 / 2pF; Unless
Min (Note 1) Typ (Note 2) Max (Note 3) Test Type
Parameter
Conditions
Units
Dynamic Performance -3dB Bandwidth -0.1dB Bandwidth Slew Rate Rise and Fall Time Rise and Fall Time Differential Gain Differential Phase 2nd Harmonic Distortion Vo = 200mVp-p Vo = 200mVp-p 4V Step O/P, 10-90% 4V Step O/P, 10-90% 200mV Step O/P, 10-90% NTSC, RL = 150 NTSC, RL = 150 158 17 195 16.4 2.4 0.01 -0.1 MHz MHz V/s ns ns % deg C C C C C C C
Distortion and Noise Response Vo = 8.4Vpp, f =100KHz,RL= 25/2pF Vo = 8.4Vpp, f =1MHz,RL = 100/2pF Vo = 2Vpp, f =100kHz,RL= 25/2pF Vo = 2Vpp, f =1MHz,RL =100/2pF 3rd Harmonic Distortion Vo = 8.4Vpp, f =100KHz,RL=25/2pF Vo = 8.4Vpp, f =1MHz,RL =100/2pF Vo = 2Vpp, f =100KHz,RL=25/2pF Vo = 2Vpp, f =1MHz,RL=100/2pF MTPR Multi-Tone Power Ratio 47.4375 KHz 69 KHz 90.5625 KHz 112.125 KHz Input Noise Voltage Input Noise Current Input Characteristics Vos Input Offset Voltage Tj = -40C to 150C - 4.2 - 0.3 4.2 mV A f = 100KHz f = 100KHz -65.4 -80.8 -93.1 -85.5 -69.9 -74.8 -82.7 -71.8 -76 -74.5 -72 -70 3.8 2.7 dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc nV/Hz pA/Hz C C C C C C C C C C C C C C
4
Zarlink Semiconductor Inc.
Data Sheet
Symbol Ib Ios CMVR CMRR Parameter Input Bias Current Input Offset Current Common Mode Voltage Range Common Mode Rejection Ratio Voltage Gain Conditions Tj = -40C to 150C Tj = -40C to 150C Tj = -40C to 150C Tj = -40C to 150C -2 - 4.9 70 79 Min (Note 1) Typ (Note 2) -10 -0.2 Max (Note 3) -20 2 4.9
ZL40162
Units A A V dB Test Type A A A A
Transfer Characteristics Avol RL = 1k, Tj = -40C to 150C RL = 25, Tj = -40C to 150C Output Swing Output Swing Isc Output Current (Note 3) Supply Current / Amp Power Supply Rejection Ratio RL = 25, Tj = -40C to 150C RL = 1k, Tj = -40C to 150C Vo = 0, Tj = -40C to 150C Tj = -40C to 150C Tj = -40C to 150C 73 4.7 1.6 - 4.5 -5 570 10 5.5 4.7 5.1 1000 4.5 5 V V mA V/mV A A A A B
Power Supply Is PSRR 7 81 9 mA dB A A
Note 1: Note 2: Note 3:
The maximum power dissipation is a function of Tj(max), JA and TA. The maximum allowable power dissipation at any ambient temperature is PD = (Tj(max) - TA)/ JA. All numbers apply for packages soldered directly onto a PC board. Typical values represent the most likely parametric norm. Test Types: a. 100% tested at 25C. Over temperature limits are set by characterisation or simulation. b. Limits set by characterisation or simulation. c. Typical value only for information.
Zarlink Semiconductor Inc.
5
ZL40162
Data Sheet
2.5V Electrical Characteristics - TA = 25C, G = +2, Vs = 2.5V, Rf = Rg = 510, RL = 100 / 2pF; Unless otherwise specified. Symbol Parameter Conditions Min (Note 1) Typ (Note 2) Max (Note 3) Units Test Type
Dynamic Performance -3dB Bandwidth -0.1dB Bandwidth Slew Rate Rise and Fall Time Rise and Fall Time Distortion and Noise Response 2nd Harmonic Distortion Vo = 2Vpp,f = 100KHz, RL = 25 Vo = 2Vpp, f = 1MHz, RL = 100 3rd Harmonic Distortion Vo = 2Vpp, f = 100KHz, RL = 25 Vo = 2Vpp, f = 1MHz, RL = 100 Input Characteristics Vos Ib CMVR CMRR Input Offset Voltage Input Bias Current Common Mode Voltage Range Common Mode Rejection Ratio Tj = -40C to 150C Tj = -40C to 150C Tj = -40C to 150C -1.55 70 80 - 4.2 - 0.3 - 10 4.2 -20 1.55 mV A V dB B B B B -92.5 -85.4 -84.4 -72.7 dBc dBc dBc dBc C C C C 1V Step O/P, 10-90% 1V Step O/P, 10-90% 200mV Step O/P, 10-90% 152.5 19 171 4.67 2.15 MHz MHz V/s ns ns C C C C C
Transfer Characteristics Avol Voltage Gain RL = 1k, Tj = -40C to 150C RL = 25, Tj = -40C to 150C Output Characteristics Output Swing RL = 25, Tj = -40C to 150C RL = 1k, Tj = -40C to 150C -1.4 -1.6 1.48 1.65 1.4 1.6 V B B 5.5 1.6 10.7 6 V/mV B B
6
Zarlink Semiconductor Inc.
Data Sheet
Min (Note 1) Typ (Note 2) Max (Note 3)
ZL40162
Parameter Conditions Units Test Type
Symbol Power Supply Is PSRR
Note 1: Note 2: Note 3:
Supply Current/Amp Power Supply Rejection Ratio
Tj = -40C to 150C Tj = -40C to 150C 73
6.75 83
8.5
mA dB
A B
The maximum power dissipation is a function of Tj(max), JA and TA. The maximum allowable power dissipation at any ambient temperature is PD = (Tj(max) - TA)/ JA. All numbers apply for packages soldered directly onto a PC board. Typical values represent the most likely parametric norm. Test Types: a. 100% tested at 25C. Over temperature limits are set by characterisation or simulation. b. Limits set by characterisation or simulation. c. Typical value only for information.
Zarlink Semiconductor Inc.
7
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Output Swing
Positive Output Swing into 1k
8
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Negative Output Swing into 1k
Positive Output Swing into 25
Zarlink Semiconductor Inc.
9
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Negative Output Swing into 25
+Vout VS lload
10
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. -Vout VS ILoad
+Vout VS ILoad, Vs = 2.5V
Zarlink Semiconductor Inc.
11
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. -Vout VS ILoad, Vs = 2.5V
Supply Current VS. Supply Voltage
12
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Sourcing Current VS. Supply Voltage
Sinking Current VS. Supply Voltage
Zarlink Semiconductor Inc.
13
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Vos VS. Vs
Vos VS. Vcm
14
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Vos VS. Vcm, Vs = 2.5V
Bias Current VS. Vsupply
Zarlink Semiconductor Inc.
15
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Offset Current VS. Vsupply
Harmonic Distortion VS. Load F = 1MHZ Vout = 2Vpp
16
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harmonic Distortion VS. Load Vs = 2.5V, F = 1MHz, Vout = 2Vpp
Harmonic Distortion VS. Output Voltage Vs = 2.5V, F = 1MHz
Zarlink Semiconductor Inc.
17
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harmonic Distortion VS. Output Voltage F = 1MHz
Harmonic Distortion VS. Output Voltage Vs = 2.5V, F = 1MHz, RL = 25
18
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harmonic Distortion VS. Output Voltage F = 1MHz, RL = 25
Harmonic Distortion VS. Output Voltage F = 10MHz
Zarlink Semiconductor Inc.
19
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harmonic Distortion VS. Output Voltage F = 10MHz, RL = 25
Harmonic Distortion VS. Frequency Vout = 2Vpp
20
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harmonic Distortion VS. Output Voltage Vs =2.5V, F = 10MHz
Harmonic Distortion VS. Frequency Vout = 2Vpp, RL = 25
Zarlink Semiconductor Inc.
21
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harmonic Distortion VS. Output Voltage Vs =2.5V, F = 10MHz, RL = 25
Harmonic Distortion VS. Frequency Vout = 2Vpp, Vs =2.5V
22
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harmonic Distortion VS. Frequency Vout = 2Vpp, Vs = 2.5V, RL = 25
Frequency Response
Zarlink Semiconductor Inc.
23
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Pulse Response
Frequency Response
24
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Pulse Response, Vs = 2.5V
Frequency Response Gain = +5
Zarlink Semiconductor Inc.
25
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Frequency Response Gain = +10
PSRR VS. Frequency
26
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. CMRR VS. Frequency
PSRR VS. Frequency Vs = 2.5V
Zarlink Semiconductor Inc.
27
ZL40162
Data Sheet
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. CMRR VS. Frequency Vs = 2.5V
Noise Voltage VS. Frequency
28
Zarlink Semiconductor Inc.
Data Sheet
ZL40162
Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Current Noise VS. Frequency
Zarlink Semiconductor Inc.
29
ZL40162
Data Sheet
30
Zarlink Semiconductor Inc.
For more information about all Zarlink products visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request.
Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE

▲Up To Search▲

Price & Availability of ZL40162DCB

	To Download ZL40162DCB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .